Zycoo UC510 User Manaual Download Page 52 | Manualshive

Page: 52 / 84

Zycoo UC510 User Manaual Download Page 52

Copyright © ZYCOO All Rights Reserved

51

/

84

Reference:

Item

Explanation

WAN Connection Type

Select LTE (Optional)

APN

Access Point Name, such as 3GNET. (mandatory field)

User Name

Set user name (Optional)

Password

Set Password (Optional)

MAC Clone

To prevent multiple users from sharing a broadband connection, the ISP will identify the MAC
address of the terminals.MAC Clone is used to clone the same MAC address of the WANport for
network connection. Multiple users can surf the internet through a single router.

Reference:

Item

Explanation

MAC Clone

Enable/Disable MAC Clone

MAC Address

Fill the cloned MAC address. E.g.: ac:7b:a1:82:be:05

4.1.2 LAN

LAN Setup

It’s necessary to configure the LAN IP for LAN based users to achieve internal network
connectivity.
Default LAN IP for UC510/520 is 192.168.1.1, and it can be changed as required.
To make changes to the settings for the LAN port, VLAN and DHCP Server.

Click

【

Internet

】



【

LAN

】

:

«
...
50
51
52
53
54
...
»

Summary of Contents for UC510





















































































Reviews:

No comments