manualshive.com logo in svg

Zycoo UC510, User Manaual, Page: 64 / 84

Share
Download
Zycoo UC510 User Manaual Download Page 64

 

 
Copyright © ZYCOO All Rights Reserved                                                                                               

63

 / 

84

 

 

Name 

Instruction 

BG Protection Mode 

BG = IEEE802.11b/g   
It  benefits  for  improving  slower  wireless  connection  access 
to router by complex multiple mode. 
The default is Auto 

Beacon Interval 

Beacons  are  packets  sent  by  a  wireless  Access  Point  to 
synchronize  wireless  devices.  Beacon  Interval  is  the  time 
between  beacon  transmissions.  The  access  speed  of  the 
wireless  client  will  be  higher  when  the  interval  value  is 
lower. 
The default is 100ms. 

Data Beacon Rate (DTIM) 

A DTIM is a countdown informing clients of the next window 
for listening to broadcast and multicast messages.   
The default is 1ms. 

Fragment Threshold 

Specifies  the  fragmentation  threshold  for  data  packets, 
when the packet length exceeds fragmentation threshold, it 
will be divided into various data packets automatically. More 
data packets will result in poor performance of the network. 
It’s not recommended to set a lower value.   
The default is 2346. 

RTS Threshold 

Specify the RTS threshold for data packets, when the packet 
length  exceeds  this  value,  the  router  will  send  the  RTS  to 
destination  for  negotiate,  after  receiving  the  RTS  frame, 
wireless  site  will respond  to  a  CTS (Clear  to  send)  frame  in 
response to the router and the client; which means there is 
wireless communication between them. 

TX Power 

Define  the  size  of  current  wireless  AP  for  SSID  transmitted 
power, the larger the signal stronger. The default is 100. 

Short Preamble 

Enable short preamble to make the network synchronization 
performance better. The default is enabled. 

Short Slot 

Enable  it  to  improve  the  transmission efficiency  of  wireless 
communication. The default is enabled. 

Tx Burst 

Enable it to assure the AP has a higher throughput without 
changing  the  network  environment  and  increasing  the 
transmission duration. Default is enabled. 

Pkt_Aggregate 

Packet Aggregate. Enable it to strengthen the mechanism of 
local  area  network  to  ensure  correct  packet  to  the 
destination 

IEEE 802.11H Support 

Extension of the 5 GHZ microwave standard of physical layer 
and  MAC  sub-layer  (mainly  used  in  Europe)It  solves 
problems like interference with satellites and radar using the 
same 5 GHz frequency band.   

Summary of Contents for UC510





















































































Reviews:

No comments