manualshive.com logo in svg

Zycoo UC510, User Manaual, Page: 48 / 84

Share
Download
Zycoo UC510 User Manaual Download Page 48

 

 
Copyright © ZYCOO All Rights Reserved                                                                                               

47

 / 

84

 

 

polarity  reversal  function,  and  meanwhile,  you  must  configure  relevant  parameters  of  polarity 
reversal in trunk configuration for the UC510/520. 

 

3.4.3  PBX Debug Logs 

Click

【

Report

】

【

System Logs

】

, you can download/ delete the system logs. 

 

 

 

 

 

 

Chapter    4  Router Gateway 

4.1 

Internet

 

4.1.1  WAN 

This page is used to configure the WAN port and clone the MAC address. 
The device supports several methods for WAN port access including STATIC(Fixed IP)/ DHCP(Auto 
Config)/ PPPoE(ADSL)/L2TP/PPTP; and UC520 supports LTE by default. 

 

Static 

Once you have selected Static, a static IP address provided by the network service provider needs 
to be inserted. Subnet mask, default gateway and other relevant information must also be set. 

Click

【

Internet

】

【

WAN

】

: 

WAN Connection Type:    Select “STATIC(Fixed IP)” 

Summary of Contents for UC510





















































































Reviews:

No comments