manualshive.com logo in svg

Zycoo UC510, User Manaual, Page: 11 / 84

Share
Download
Zycoo UC510 User Manaual Download Page 11

 

 
Copyright © ZYCOO All Rights Reserved                                                                                               

10

 / 

84

 

 

 

Reference: 

Item 

Explanation 

SIP/IAX2 

Choose extension protocol. 

Name 

Extension Name (English Character Only), e.g.: Tom. 

Extension 

Extension Number connected to the phone, e.g.: 888. 

Password 

Same password as voicemail. (4-16 digits, e.g.:123456) 

Outbound CID 

Override the caller ID when dialing out with a trunk. 

Dial Plan 

Please  choose  the  Dial  Plan  which  is  defined  in  the  menu  “Outbound 
Routes”. 

Analog Phone 

Please choose the relative FXS port for your analog phone. 

Enable 

Enable the voicemail account 

VM Password 

Set  password  for  Voicemail.  For  security  reasons,  do  not  use  the 
extension number or any easy combination for example "1234" 

Delete VMail 

Delete voicemail from the PBX after it’s sent by email. 

Email 
(FAX/Voicemail) 

Extension user’s email address to receive email messages with attached 
fax or voicemail (you need configure the fax to email/voicemail options), 
e.g.: [email protected] 

Summary of Contents for UC510





















































































Reviews:

No comments