YOKOGAWA Admag TI AXG User Manual Download Page 284

Page: 284 / 306

<Appendix 5. PID Block>

283

IM 01E21A02-03EN

A5.4.2 PID Control Algorithm Parameters

The table below shows setting parameters for the PID control algorithm.

Parameter

Description

Valid Range

GAIN

Proportional

gain

0.05 to 20

RESET

Integral time

0.1 to 10000

(seconds)

RATE

Derivative

time

0 to infinity

(seconds)

A5.5 Control Output Action

The control output action is the function to convert the change in operation output (ΔMVn) at

each control period to the actual operation output value (OUT).

The control output action for the PID block of EJX supports the velocity-type.

A5.5.1 Velocity Type

The PID block determines the value of the new control output (OUT) by adding the change in

control output calculated in the current control period (ΔMVn) to the value read back from the

output destination (BKCAL_IN).

The calculation expression for the control output action of speed type is shown below.

ΔMVn’= ΔMVn*(OUT_SCALE. EU100 - OUT_SCALE. EU_0) / (PV_SCALE.
  EU_100 - PV_SCALE. EU_0)
(Direct Acting is False in CONTROL_OPTS)
  OUT = BKCAL_IN - ΔMVn’
(Direct Acting is True in CONTROL_OPTS)
  OUT = BK ΔMVn’

A5.6 Direction of Control Action

The operating direction of the output is switched for the increase or decrease of the deviation.

The direction is specified with Direct Acting of CONTROL_OPTS.

Value of Direct

Acting

Description

True

The output increases when the measured value (PV) is

greater than the setpoint (SP).

False

The output decreases when the measured value (PV) is

greater than the setpoint (SP).

Summary of Contents for Admag TI AXG



















































































































































































































































































































Search results

Summary of Contents for Admag TI AXG

Reviews:

Brands by name

Popular brands

YOKOGAWA Admag TI AXG, User Manual

Search results

Summary of Contents for Admag TI AXG

Reviews:

Brands by name

Popular brands