manualshive.com logo in svg

YASKAWA 2A0001, Technical Manual, Page: 302 / 512

Share
Download
YASKAWA 2A0001 Technical Manual Download Page 302

Cause

Possible Solutions

The motor is running at almost 0 Hz and the Speed

Search estimated the speed to be in the opposite

direction.

• Disable bi-directional search (b3-14 = “0”) so that Speed Search is performed only in the

specified direction.

Note:

Check the motor specifications for the forward and reverse directions. The motor specifications will vary depending on the manufacturer

of the motor.

n

Motor Rotates in One Direction Only

Cause

Possible Solutions

The drive prohibits reverse rotation.

• Check parameter b1-04.
• Set the drive to allow the motor to rotate in reverse (b1-04 = “0”).

A Reverse run signal has not been entered, although

3-Wire sequence is selected.

• Make sure that one of the input terminals S3 to S7 used for the 3-Wire sequence has been set

for reverse.

n

Motor is Too Hot

Cause

Possible Solutions

The load is too heavy.

If the load is too heavy for the motor, the motor will overheat as it exceeds its rated torque value

for an extended period of time.

Keep in mind that the motor also has a short-term overload rating in addition to the possible

solutions provided below:
• Reduce the load.
• Increase the acceleration and deceleration times.
• Check the values set for the motor protection (L1-01, L1-02) as well as the motor rated current

(E2-01).

• Increase motor capacity.

The air around the motor is too hot.

• Check the ambient temperature.
• Cool the area until it is within the specified temperature range.

The drive is operating in a vector control mode but

Auto-Tuning has not yet been performed.

• Perform Auto-Tuning.
• Calculate the motor value and reset the motor parameters.
• Change the motor control method to V/f Control (A1-02 = “0”).

Insufficient voltage insulation between motor phases.

When the motor is connected to terminals U/T1, V/T2, and W/T3, voltage surges occur between

the motor coils and drive switching.

Normally, surges can reach up to three times the drive input power supply voltage (600 V for 200

V class, and 1200 V for 400 V class).
• Use a motor with voltage tolerance higher than the max voltage surge.
• Use a motor designed to work specifically with a drive when using a 400 V class unit.
• Install an AC reactor on the output side of the drive.

The motor fan has stopped or is clogged.

Check the motor fan.

n

Drive Does Not Allow Selection of Rotational Auto-Tuning

Cause

Possible Solutions

The drive is in the incorrect motor control method for

Rotational Auto-Tuning.

• Check if the drive is set to V/f Control by accident (A1-02 = 0).
• Change the motor control method to Open Loop Vector Control (A1-02 = “2”).

n

Motor Hunting Occurs at Low Speeds

Cause

Possible Solutions

Excessive load inertia in Open Loop Vector Control.

• Excess load inertia can cause motor hunting in Open Loop Vector Control due to slow motor

response.

• Increase the speed feedback detection control time constant (n2-02) from its default value of

50 ms to an appropriate level between 200 and 1000 ms. Adjust this setting in combination

with n2-03 (Feedback Detection Control Time Constant 2).

6.9 Troubleshooting without Fault Display

302

YASKAWA ELECTRIC SIEP C710606 18F YASKAWA AC Drive – V1000 Technical Manual

Summary of Contents for 2A0001

































































































































































































































































































































































































































































































































Reviews:

No comments