YASKAWA 2A0001, Technical Manual, Page: 184 / 512

5.7 H: Terminal Functions
H parameters are used to assign functions to the external terminals.
u
H1: Multi-Function Digital Inputs
n H1-01 to H1-07: Functions for Terminals S1 to S7
These parameters assign functions to the multi-function digital inputs. Settings 0 to 9F determine function for each terminal
and are explained below.
Note: 1. Terminals that are not used and terminals using the through-mode should be set to “F”.
2. Drive software versions PRG: 1013 and later require that the Forward run and Reverse Run commands be set simultaneously.
No. Parameter Name
Setting
Range
Default
H1-01 Digital Input S1 Function Selection 1 to 9F 40: Forward Run Command (2-wire sequence)
H1-02 Digital Input S2 Function Selection 1 to 9F 41: Reverse Run Command (2-wire sequence)
H1-03 Digital Input S3 Function Selection 0 to 9F 24: External Fault (N.O., always detected, coast to stop)
H1-04 Digital Input S4 Function Selection 0 to 9F 14: Fault Reset
H1-05 Digital Input S5 Function Selection 0 to 9F
3 (0)
<1>
: Multi-Step Speed Reference 1
H1-06 Digital Input S6 Function Selection 0 to 9F
4 (3)
<1>
: Multi-Step Speed Reference 2
H1-07 Digital Input S7 Function Selection 0 to 9F
6 (4)
<1>
: Jog Reference Selection
<1> Number appearing in parenthesis is the default value after performing a 3-Wire initialization.
Table 5.26 Digital Multi-Function Input Settings
Setting Function Page
0 3-Wire Sequence 185
1 LOCAL/REMOTE Selection 185
2 External Reference 1/2 186
3 Multi-Step Speed Reference 1
186 4 Multi-Step Speed Reference 2
5 Multi-Step Speed Reference 3
6 Jog Reference Selection 186
7 Accel/Decel Time 1 186
8 Baseblock Command (N.O.)
186
9 Baseblock Command (N.C.)
A Accel/Decel Ramp Hold 186
B Drive Overheat Alarm (oH2) 187
C Terminal A1/A2 Enable/Disable 187
F Not used/Through Mode 187
10 Up Command
187
11 Down Command
12 Forward Jog
188
13 Reverse Jog
14 Fault Reset 188
15 Fast-Stop (N.O.) 188
16 Motor 2 Selection 189
17 Fast-stop (N.C.) 188
18 Timer Function Input 189
19 PID Disable 189
1A Accel/Decel Time Selection 2 189
1B Program Lockout 189
1E Reference Sample Hold 190
20 to 2F External Fault 190
Setting Function Page
30 PID Integral Reset 191
31 PID Integral Hold 191
32 Multi-Step Speed Reference 4 191
34 PID Soft Starter Cancel 191
35 PID Input Level Selection 191
40 Forward Run/Stop (2-wire sequence)
191
41 Reverse Run/Stop (2-wire sequence)
42 Run/Stop (2-Wire sequence 2)
191
43 FWD/REV (2-Wire sequence 2)
44 Offset Frequency 1 Addition
192 45 Offset Frequency 2 Addition
46 Offset Frequency 3 Addition
47
<1>
Node Setup 192
60 DC Injection Braking Command 192
61 External Speed Search Command 1
192
62 External Speed Search Command 2
65 KEB Ride-Thru 1 (N.C.)
192
66 KEB Ride-Thru 1 (N.O.)
67 Communications Test Mode 192
68 High-Slip Braking 192
6A Drive Enable 192
75 Up 2 Command
193
76 Down 2 Command
7A KEB Ride-Thru 2 (N.C.)
194
7B KEB Ride-Thru 2 (N.O.)
7C Short-Circuit Braking (N.O.)
194
7D Short-Circuit Braking (N.C.)
5.7 H: Terminal Functions
184 YASKAWA ELECTRIC SIEP C710606 18F YASKAWA AC Drive – V1000 Technical Manual