Yamaha YZ250F(N)/LC Owner'S Service Manual Download Page 567

Page: 567 / 656

5 - 57

CHAS

AMORTISSEUR ARRIERE

FEDERBEIN

AMMORTIZZATORE POSTERIORE

FEDERBEIN

Demontage-Arbeiten:

Federbein demontieren

Federbein zerlegen

Demontage-Arbeiten

Reihen-

folge

Bauteil

Anz.

Bemerkungen

Vorbereitung für den Ausbau

FEDERBEIN DEMONTIEREN
Das Motorrad am Motor aufbocken.

WARNUNG

Das Motorrad gegen Umfallen sichern.

Sitzbank

Siehe Abschnitt “SITZBANK, KRAFTSTOFFTANK
UND SEITENABDECKUNGEN”.

Schalldämpfer

Siehe Abschnitt “AUSPUFF UND SCHALLDÄMP-
FER” in KAPITEL 4.

Schraube (Bremsflüssigkeitsbehälter)

Schlauchschelle (Luftfilteranschluß)

Nur lockern.

Rahmenhinterteil

Schraube (Umlenkhebel, Federbein)

Die Schwinge festhalten.

Schraube (Federbein, Rahmen)

Federbein

Sicherungsmutter

Nur lockern.

Einstellmutter

Nur lockern.

Unterer Federsitz

AMORTISSEUR ARRIERE

Organisation de la dépose:

Dépose de l’amortisseur arrière

Démontage de l’amortisseur arrière

Organisation de la dépose

Ordre

Nom de pièce

Qté

Remarques

Préparation pour la dépose

DEPOSE DE L’AMORTISSEUR
ARRIERE
Maintenir la machine en plaçant un support
approprié sous le moteur.

AVERTISSEMENT

Bien soutenir la machine afin qu’elle ne risque

pas de se renverser.

Selle

Se référer à la section “SELLE, RESERVOIR A
ESSENCE ET CACHES LATERAUX”.

Silencieux

Se référer à la section “TUYAU D’ECHAPPEMENT ET
SILENCIEUX” du CHAPITRE 4.

Boulon (réservoir)

Bride (raccord de filtre à air)

Desserrer uniquement.

Cadre arrière

Boulon (amortisseur arrière-bras de relais)

Tenir le bras oscillant.

Boulon (amortisseur arrière-cadre)

Amortisseur arrière

Contre-écrou

Desserrer uniquement.

Dispositif de réglage

Desserrer uniquement.

Guide de ressort inférieur

AMMORTIZZATORE POSTERIORE

Portata dello smontaggio:

Rimozione ammortizzatore posteriore

Smontaggio ammortizzatore posteriore

Portata dello smontaggio

Ordine

Denominazione

Quantità

Osservazioni

Preparazione per la rimozione

RIMOZIONE AMMORTIZZATORE
POSTERIORE
Mantenere il veicolo posizionando un supporto
idoneo sotto al motore.

AVVERTENZA

Sostenere saldamente il veicolo in modo che non ci sia
il rischio che si rovesci.

Sella

Fare riferimento al paragrafo “SELLA, SERBATOIO
DEL CARBURANTE E CARENATURA LATERALE”.

Silenziatore

Fare riferimento al paragrafo “TUBO DI SCARICO E
SILENZIATORE” nel CAPITOLO 4.

Bullone (serbatoio)

Morsetto (giunto filtro dell’aria)

Allentare soltanto.

Telaio posteriore

Bullone (ammortizzatore posteriore - leva di
rinvio)

Sostenere il forcellone oscillante.

Bullone (ammortizzatore posteriore - telaio)

Ammortizzatore posteriore

Controdado

Allentare soltanto.

Registro

Allentare soltanto.

Guida molla inferiore

Summary of Contents for YZ250F(N)/LC

















































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for YZ250F(N)/LC

Reviews:

Related manuals for YZ250F(N)/LC

Brands by name

Popular brands

Yamaha YZ250F(N)/LC, Owner'S Service Manual

Search results

Summary of Contents for YZ250F(N)/LC

Reviews:

Related manuals for YZ250F(N)/LC

Brands by name

Popular brands