Yamaha MOTIF XF Reference Manual Download Page 61

Page: 61 / 255

Editing a Normal Voice

MOTIF XF Reference Manual

oice mode

Song mode

n mode

Mixing mode

Mast

er mode

Utility mode

ile mode

erf

mance

mode

Sampling

mode 1

Sampling

mode 2

rence

Controller settings—[F4] Ctrl Set
(Controller Set)

The controllers such as knobs on the front panel can be
used to change and adjust a variety of parameters for each
Voice—in real time, and simultaneously. For example,
keyboard aftertouch can be used to control vibrato and the
Modulation Wheel could be used to control tonal
brightness.
The function settings for all the controllers are referred to as
a “Controller Set,” and up to six Controller Sets can be
created for each Voice. The controller is referred to as
Source, and the controlled function is referred to as
Destination. From this display, you can determine the
Controller Sets.

Depending on the selected parameter, the LIST icon is shown
at the tab menu corresponding to the [SF6] button. In this
condition, you can call up the list by pressing the [SF6] LIST
button, then select the desired item from the list. For details,
see page 37.

Source*

Determines which panel controller is to be assigned and
used for the selected Set. You can also assign multiple
functions to a controller. You can set this parameter by
operating the desired controller while holding the [SF5]
Controller button.

Settings:

PitchBend

Indicates the built-in Pitch Bend wheel.

ModWheel

Indicates the built-in Modulation wheel.

AfterTch (Aftertouch)

Indicates the event generated when pressure is applied to a key after
the note is played.

FootCtrl1 (Foot Controller2)
FootCtrl2 (Foot Controller2)

Indicates the Foot Controller connected to each of the FOOT
CONTROLLER 1 and 2 jacks on the rear panel.

FootSw (Footswitch)

Indicates the Footswitch connected to the FOOT SWITCH
ASSIGNABLE jack on the rear panel.

Ribbon

Indicates the built-in Ribbon Controller.

Breath

Indicates the external controller which sends the control change
number assigned to the Breath Controller in the Utility mode
(page 230) to the MOTIF XF via MIDI.

Assign1
Assign2

Indicates the Knobs printed “ASSIGN 1” and “ASSIGN 2” with the
TONE 1 lamp turned on.

A. Func 1
A. Func 2

Indicates the built-in ASSIGNABLE FUNCTION [1] and [2] buttons.

You can determine the degree to which the Pitch Bend wheel
affects the Destination parameter (below) by setting the Pitch
Bend Range Upper (

) and Pitch Bend Range Lower (

) in

the Play Mode display (page 55).

Destination*

Determines the parameter that is controlled by the Source
controller (above). You can select a parameter for each
controller from the 67 parameters, such as volume, pitch
and LFO depth.

Settings:

Refer to the Control List in the separate Data List.

Regarding “Insertion Effect A Parameter 1 – 16,” “Insertion
Effect B Parameter 1 – 16” and “Insertion Effect L Parameter 1
– 32” described in the Control List, the actual parameter
names of the selected Effect type are shown on the display. If
one of these names is shown, no function is assigned to that
parameter.

Setting examples of the Destination

Concerning *1 – *4, the following settings are necessary in addition to
the above setting.

Depth*

Determines the degree to which the Source controller
affects the Destination parameter. For negative values, the
controller operation is reversed; maximum controller
settings produce minimum parameter changes.

Settings:

-64 – +0 – +63

Element Switch*

Determines whether or not the selected controller affects
each individual element. This parameter is disabled when
the Destination (

) described above is set to a parameter

unrelated to the Voice Elements.

To control the volume:

Volume

To apply vibrato to the Voice:

Common LFO Depth 1 – 3
(C-LFO dpth1 – 3) *1

To change the pitch:

Element Pitch
(coarse tune) *2