CABLE ROUTING (FJR13ESG)
2-74
1. Headlight beam adjusting knob shaft
2. Headlight sub-wire harness
3. Relay unit lead
4. Relay unit
5. Radiator fan motor lead (left)
6. Windshield drive unit relay lead (down)
7. Accessory box solenoid sub-wire harness coupler
8. Auxiliary DC jack coupler
9. Front turn signal/position light coupler (left)
10. Windshield drive unit relay lead (up)
11. Wire harness
12. Windshield drive unit coupler
13. Windshield drive unit cable
14. Windshield drive unit sub-wire harness
15. Windshield drive unit sub-wire harness coupler
16. Meter assembly lead
17. Grip warmer lead
18. Front brake light switch coupler
19. Electrical components board
20. Grip warmer coupler
21. Clutch switch coupler
22. Handlebar switch coupler (left)
23. Air temperature sensor lead
24. Handlebar switch coupler (right)
A. Towards the front of the vehicle
B. Make sure that the handlebar switch leads, grip
warmer leads, front brake light switch lead, and
clutch switch lead are not resting on top of the relay
bracket.
C. Secure the plastic band by inserting the projection
on the band into the hole in the relay bracket, and
then fasten the handlebar switch leads, grip
warmer leads, front brake light switch lead, and
clutch switch lead with the band. Face the end of
the plastic band outward. Do not cut off the excess
end of the plastic band.
D. Insert the projection on the wire harness holder
completely into the hole in the relay bracket.
E. From electrical components tray
F. Route the relay unit lead to the rear of the
headlight beam adjusting knob shaft.
G. Route the relay leads, meter assembly lead, and
handlebar switch leads, grip warmer leads, front
brake switch lead, and clutch switch lead in the
order listed from top to bottom.
H. Fasten the wire harness at the white tape on both
portions of the harness with a plastic locking tie.
Position the end of the plastic locking tie under the
meter assembly, facing inward. Do not cut off the
excess end of the plastic locking tie.
I.
Route the wire harness between the relay bracket
and windshield drive unit bracket.
J. Route the windshield drive unit sub-wire harness
to the front of the windshield cable.
K. Insert the projection on the windshield drive unit
sub-wire harness coupler completely into the hole
in the electrical components board.
L. Secure the holder by inserting the projection on
the holder into the hole in the electrical
components board, and then fasten the handlebar
switch leads, grip warmer leads, front brake light
switch lead, clutch switch lead, and meter
assembly lead with the holder. Face the catch of
the holder upward.
M. Route the grip warmer leads to the inside of the rib
on the electrical components board.
N. Insert the projection on the front brake light switch
coupler completely into the hole in the electrical
components board.
O. Insert the projection on the clutch switch coupler
completely into the hole in the electrical
components board.
P. Insert the projection on the wire harness holder
completely into the hole in the electrical
components board.
Q. Insert the projection on left handlebar switch
coupler completely into the hole in the electrical
components board.
R. Route the air temperature sensor lead under the
left handlebar switch leads.
S. Insert the projection on right handlebar switch
coupler completely into the hole in the electrical
components board.
Summary of Contents for FJR13AG
