Xerox DocuColor 12/DCCS50, Service Manual

Page: 787 / 1617

1/05
6-107 DocuColor 12/DCCS50
dC330 Component Control
General Procedures
Reissue
004-007 MAIN MOTOR Output The Main Motor rotates at a fre-
quency of 2000.8 Hz
The PR and IVT are turned on
simultaneously
IF you operate the Drum Motor and
the main Motor at the same time,
then start one of them, the other
Motor will shut down. (This is
because they are both using the
same Hard signal)
Processor
004-009 FUSER MOTOR Output The fuser motor rotates with a fre-
quency of 1495.886 Hz.
Note: also used with V-TRA Processor
004-021 DRUM MOTOR Output - The drum motor rotates with a
frequency of 1495.886 Hz.
- Drum Motor Gain sell, 2 (low)
- PR and IBT are turned on simul-
taneously
- If you operate the drum motor
and the main motor at the same
time, then stop one of them, the
other motor will slow down. (This is
because they are both using the
same hard signal) Processor
005-011 SET GATE SOLENOID
OPEN
Output After 5 sec., turned OFF automati-
cally DADF
005-012 SET GATE SOLENOID
CLOSE
Output After 5 sec., turned OFF automati-
cally DADF
005-040 FEED MOTOR Output After 2 sec., turned OFF automati-
cally DADF
005-055 BELT MOTOR CW Output The DADF Belt Motor forwards DADF
005-056 BELT MOTOR CCW Output Belt Motor (Normal rotation)
The DADF Belt Motor reverses DADF
005-075 REGI GATE SOLE-
NOID
Output After 5 sec., turned OFF automati-
cally DADF
005-081 EXIT MOTOR Output On: Rotates DADF
005-083 DOC READY Output Simultaneous Output item: (IISS
sheet abort) DADF
005-084 DOC SET LED Output On: L DADF
006-002 ITT EXPOSURE LEAP Output After 180 sec., Turns OFF automat-
ically IIT
Table 2 Output Component Control Codes
ID Description In_Out Smart Help
Module_I
D
006-003 COOLING FAN LOW
SPEED
Output ON: L
Cooling Fan: High IIT
006-005 IIT SCAN MOTOR
(Scan)
Output Moves the Carriage 50mm in the
scan direction and stops automati-
cally IIT
006-006 IIT SCAN MOTOR
(Return)
Output IIT Scan Motor (Return) IIT
006-007 FUSER CUT Output On: Active IIT
006-013 COOLING FAN HIGH
SPEED
Output On: L IIT
006-086 IIT IMAGE AREA Output On: Active IIT
006-091 EXCHANGE TO ADF Output On: Active
Simultaneous on item IIT
007-078 HCF FEED CLUTCH Output Engages the HCF Nudger Roll to
the Feed Motor. HCF
007-079 HCF ELEVATE MOTOR Output Unidirectional Motor to move the
HFC Paper Tray in the up direction
only (motor is not engaged in the
down direction). HCF
007-080 HCF FEED MOTOR Output Unipolar 200 step / rev stepper
motor with a maximum 800 PPS.
One revolution = 200 steps = 152
mm paper travel. HCF
008-006 #1 NUDGER ROLL
SOLENOID
Output ON time is 2000 msec Processor
008-007 #1 FEED MOTOR CCW Output Motor reverse. Tray lift up (upper
limit detection stop)
ON time: 5500 msec Processor
008-008 #1 FEED MOTOR CW Output Motor normal rotation: Feed Roll
rotation Processor
008-009 #1 TAKE AWAY FEED
CLUTCH
Output On drives connection Processor
008-011 #2 NUDGER ROLL
SOLENOID
Output ON time is 2000 msec Processor
008-012 #2 FEED MOTOR CCW Output Motor reverse: Tray lift up (upper
limit detection stop)
Does not turn on if the tray is not
set
ON time: 6000 msec Processor
Table 2 Output Component Control Codes
ID Description In_Out Smart Help
Module_I
D