Xerox DocuColor 12/DCCS50, Service Manual

Page: 793 / 1617

1/05
6-113 DocuColor 12/DCCS50
dC330 Component Control
General Procedures
Reissue
012-030 END WALL MOTOR
OPEN
Output High: On
Drives End Wall to open it (300ms) Finisher
012-031 END WALL MOTOR
CLOSE
Output High: On
Drives End Wall to close it (300ms) Finisher
012-036 COMPILER TRAY
SOLENOID
Output Low: On
Lowers Compiler Tray. Finisher
012-040 STACKER MOTOR UP Output High: On
No output is allowed if a response
is sensed from Tray Upper Limit
SNR before or while Stacker Tray
being driven upward. (500ms)
Finisher
012-041 STACKER MOTOR
DOWN
Output High: On
No output is allowed if a response
is sensed from Tray Upper Limit
SNR before or while Stacker Tray
being driven downward.
Finisher
012-053 EJECT PADDLE
MOTOR
Output High: On
Drives Set Clamp. (300ms) Finisher
012-060 TAMPER MOTOR LOW
FRONT
Output Not measurable
Drives Tamper to front at a low
speed. (560pps) (100 pulses)
Note: Not measurable in field due to
24V Clock. Finisher
012-061 TAMPER MOTOR TOP
FRONT
Output Not measurable
Drives Tamper to front at a high
speed. (2000pps) (100 pulses)
Note: Not measurable in field due to
24V Clock. Finisher
012-062 TAMPER MOTOR LOW
REAR
Output Not measurable
Drives Tamper to rear at a low
speed. (560pps) (100 pulses)
Note: Not measurable in field due to
24V Clock. Finisher
012-063 TAMPER MOTOR TOP
REAR
Output Not measurable
Drives Tamper to rear at a high
speed. (2000pps) (100 pulses)
Note: Not measurable in field due to
24V Clock. Finisher
012-064 TAMPER MOTOR MID-
DLE FRONT
Output Not measurable
Drives Tamper to front at a medium
speed. (1000pps) (100 pulses)
Note: Not measurable in field due to
24V Clock. Finisher
Table 2 Output Component Control Codes
ID Description In_Out Smart Help
Module_I
D
012-065 TAMPER MOTOR MID-
DLE REAR
Output Not measurable
Drives Tamper to rear at a medium
speed. (1000pps) (100 pulses)
Note: Not measurable in field due to
24V Clock. Finisher
012-070 FIN GATE SOLENOID-
MBX/SCT POSITION
Output Low: On
Switches Gate for MBX/SCT. (100
pulses) Finisher
012-071 FIN GATE SOLENOID-
FINSHER POSITION
Output Low: On
Switches Gate for Finisher. (100
pulses) Finisher
012-075 STAPLER MOTOR
CLOSE
Output High: On
Does stapling. (Compiler cover
Safety ON) (Stops at Home or
times out in 500ms). Finisher
012-076 STAPLE POSITION
MOTOR TOP FRONT
Output Not measurable
Drives Stapler Unit to front at a high
speed (2700pps). If End Wall Open
Sensor doesn’t sense any, no out-
put is allowed. (250 pulses). Finisher
012-077 STAPLE POSITION
MOTOR LOW FRONT
Output Not measurable
Drives Stapler Unit to front at a low
speed (2000pps). If End Wall Open
Sensor doesn’t sense any, no out-
put is allowed. (250 pulses).
Note: Not measurable in field due to
24V Clock Finisher
012-078 STAPLE POSITION
TOP REAR
Output Not measurable
Drives Stapler Unit to rear at a high
speed (2700pps). If End Wall Open
Sensor doesn’t sense any, no out-
put is allowed. (250 pulses).
Note: Not measurable in field due to
24V Clock Finisher
012-079 STAPLE POSITION
MOTOR LOW REAR
Output Not measurable
Drives Stapler Unit to rear at a low
speed (2000pps). If End Wall Open
Sensor doesn’t sense any, no out-
put is allowed. (250 pulses).
Note: Not measurable in field due to
24V Clock Finisher
012-081 MBX GATE SOLE-
NOID CLOSE
Output Low: On
Switches MBX Gate for SCT.
(150ms) Finisher
Table 2 Output Component Control Codes
ID Description In_Out Smart Help
Module_I
D