Xerox DocuColor 12/DCCS50, Service Manual

Page: 788 / 1617

1/05
6-108 DocuColor 12/DCCS50
dC330 Component Control
Reissue
General Procedures
008-013 #2 FEED MOTOR CW Output Motor normal rotation: Feed Roll
rotation Processor
008-014 #2 TAKE AWAY FEED
CLUTCH
Output On drives connection Processor
008-016 #3 NUDGER ROLL
SOLENOID
Output ON time is 2000 msec Processor
008-017 #3 FEED MOTOR CCW Output Motor reverse: Tray lift up (upper
limit detection stop)
Does not turn on if the tray is not
set.
ON time: 6000 msec
Processor
008-018 #3 FEED MOTOR CW Output Motor normal rotation: Feed roll
rotation Processor
008-019 #3 TAKE AWAY FEED
CLUTCH
Output On drives connection Processor
008-021 #4 NUDGER ROLL
SOLENOID
Output ON time is 2000 msec Processor
008-022 #4 FEED MOTOR CCW Output Motor reverse: Tray lift up (upper
limit detection stop)
Does not turn on if the tray is not
set
ON time: 6000 msec
Processor
008-023 #4 FEED MOTOR CW Output Motor normal rotation: Feed Roll
rotation Processor
008-024 #4 TAKE AWAY FEED
CLUTCH
Output On drives connection Processor
008-025 TAKE AWAY MOTOR Output On (rotation) Processor
008-030 Tray 5 NUDGER ROLL
SOLENOID
Output x Processor
008-037 TRAY 5 FEED CLUTCH Output On drives connection Processor
008-049 TRAY 5 LIFTER
MOTOR CCW (up)
Output x Processor
008-042 TRAY 5 LIFTER
MOTOR CW (down)
Output Lower limit detection stop ON time:
300 msec
Tray 5 Lift Motor CCW Processor
008-043 MAIN MOTOR 2 Output On: Port (L) Processor
008-054 REGI MOTOR Output On: Port (L) Processor
Table 2 Output Component Control Codes
ID Description In_Out Smart Help
Module_I
D
009-011 CARTRIDGE MOTOR K Output Automatically turns OFF after 10
sec.
Cannot run with Cartridge Motors Y
(009-012), M (009-013), or C (009-
014)
Processor
009-012 CARTRIDGE MOTOR Y Output Automatically turns OFF after 10
sec.
Cannot run with Cartridge Motors
M (009-013), C (009-014) or K
(009-011).
Processor
009-013 CARTRIDGE MOTOR
M
Output Automatically turns OFF after 10
sec.
Cannot run with Cartridge Motors Y
(009-012), C (009-014) or K (009-
011).
Processor
009-014 CARTRIDGE MOTOR
C
Output Automatically turns OFF after 10
sec.
Cannot run with Cartridge Motors Y
(009-012), C (009-013) or K (009-
011).
Processor
009-018 ROTARY LOCK MECH
LATCH
Output Latch - High: Rotary Lock SEL
RETN
Low: Rotary Lock SEL SUCF
Release - High: Rotary Lock SEL
RETN Processor
009-021 DEVE MOTOR
CLUTCH
Output On (High): Latch
Off (Low): Release Processor
009-025 IBT ROLL CONTACT Output Run simultaneously with Main
Motor (004-007)
Automatically turns OFF after the
Roll Retract Home Position Sensor
detects the Contact Position (On:
Low, Off: High)
Processor
009-026 IBT ROLL RETRACT Output Run simultaneously with Main
Motor (004-007)
Automatically turns OFF after the
Roll Retract Home Position Sensor
detects the Retract Position (On:
Low, Off: High) Processor
009-031 DISPENSE MOTOR K Output Start after moving the Rotary to the
K color and dispensing the toner.
NOTE: To drive the rotary, Move the
rotary to the K color in dC920
(Developer Unit Check). Processor
Table 2 Output Component Control Codes
ID Description In_Out Smart Help
Module_I
D
manuals4you.com manuals4you.com