Xerox DocuColor 12/DCCS50, Service Manual

Page: 1166 / 1617

1/05
8d-24 DocuColor 12/DCCS50
11-302 Decurler Door Interlock Open RAP, 11-303
Reissue
Finisher/Sorter
11-302 Decurler Door Interlock Open RAP
Decurler Door Interlock Open Failure. This status code is declared when the Decurler Front
Cover is open.
Initial Actions
• Refer to BSD12.1 for the following procedure.
• Ensure that P/J1033 on the Finisher PWB, and P/J1018 on the Decurler Door Interlock
Switch are connected before beginning this RAP.
• Check the Front Cover for proper alignment.
• Verify that the Front Cover closes properly.
Procedure
Enter dC330 012-302 Decurler Door Intlk Sw. The state of the Decurler Door Interlock
Switch is Low and switches to High when the Decurler Door is opened.
Y
N
With the Front Cover closed, there is +0 VDC between
P/J1028 -B6 on the Finisher
PWB and GND.
Y
N
Go to the Flag 1 and Flag 2 on BSD12.1. Check the wires for an open circuit. If the
wires are good, replace the Decurler Door Interlock Switch ( PL 18.11 ). If the problem
continues, replace the Decurler PWB ( PL 18.6 ). If the problem continues, replace
the Finisher PWB ( PL 18.4 ).
Check the Decurler Door Interlock Switch for intermittent operation. Ensure that the
switch and the cover are properly aligned and adjusted. If the problem continues, replace
the Decurler PWB (
PL 18.6 ). If the problem continues, replace the Finisher PWB ( PL
18.4 ).
Check the Decurler Door Interlock Switch for intermittent operation. Ensure that the switch and
the cover are properly aligned and adjusted. If the problem continues, replace the Finisher
PWB (
PL 18.4 ).
11-303 Docking Interlock Open RAP
Docking Interlock Open failure. This status code is declared when the Mailbox is not properly
docked.
Initial Actions
• Refer to BSD12.1 for the following procedure.
• Ensure that P/J1028 on the Finisher PWB, P/J664 and P/J665 on the Docking Interlock
Switches, P/J651 and P/J652 on the Decurler PWB are connected before beginning this
RAP.
• Check the Finisher/Mailbox for proper alignment.
Procedure
Enter dC330 012-303 Mailbox Docking INTLK Switches. The status of the Docking Inter-
lock Switches is High and changes to Low when the Mailbox is undocked.
Y
N
With the Finisher/Mailbox docked, there is +5 VDC between
P/J1028 -B7 on the Fin-
isher PWB and GND.
Y
N
Disconnect P/J665 from the Docking Interlock Switch 2. With the Finisher/Mail-
box docked, there is +5 VDC between P/J1028 -B7 on the Finisher PWB and
GND.
Y
N
Disconnect P/J664
from the Mailbox Docking Interlock Switch 1. With the Fin-
isher/Mailbox docked, there is +5 VDC between P/J1028 -B7 on the Fin-
isher PWB and GND.
Y
N
Go to the Flag 10 , Flag 11 and Flag 13 on BSD12.1. Check the wires for
an short circuit to ground. If the wires are good, replace the Finisher PWB
(
PL 18.4 ).
Replace the Docking Interlock Switch 1 ( PL 18.6 ).
Replace the Docking Interlock Switch 2 ( PL 18.6 ).
Check the Docking Interlock Switches for intermittent operation. Ensure that the switches
are properly aligned and adjusted. If the problem continues, replace the Finisher PWB
(
PL 18.4 ).
Check the Mailbox Door Interlock Switch for intermittent operation. Ensure that the switch and
the cover are properly aligned and adjusted. Check that the Finisher/Mailbox is standing on an
even floor. Adjust Castors if necessary. If the problem continues, replace the Mailbox PWB (
PL
18.11 ).
manuals4you.com manuals4you.com