Removing of camshaft bearing bush
14.3.3 Mounting of camshaft bearing bush
1 Lightly lubricate the new bearing bush
with clean en-
gine oil on the outer surface and put it on the guide sleeve
3V83H164. The notch on the bearing bush side should be
positioned downwards, i.e. lubricating hole in the engine block
and the oil hole in the bearing bush must be in the same
position.
2 Assemble the mounting device
according to Fig 14-4.
Notice the difference in tool assembly for the bearing next to
the flywheel end of the engine.
3 Tighten the hydraulic tool
3V83E61 by tensioning the
pull screw 4V83G45 lightly.
4 Connect the hoses of the hydraulic pump
800053 to
the hydraulic tool.
5 Pump pressure to the hydraulic tool
to mount the bear-
ing bush. The pressure must not exceed the value stated in
chapter 07, Fig 07-14.
6 Open the pump valve for removing the pressure,
disconnect the hoses of the hydraulic tool and dismantle the
mounting device.
7 Check that the oil hole in the bearing bush
is in the
correct position.
8 Lubricate the bearing surface of the bearing bush
and
insert the camshaft bearing journal.
9 Mount the camshaft pieces,
bearing journals, guide blocks,
injection pumps and camshaft covers according to the section
14.2.3.
1
2
3V83H165
3V83H166
3V83G45
3V83E61
3V83H164
Bearing
3V83H61 Hydraulic cylinder
3V83H164 Guide sleeve
3V83H165 Distance piece
3V83H166 Pressure plate
4V83G45 Screw
Fig 14-3
4014019601
32-200106
Valve Mechanism and Camshaft
14
WÄRTSILÄ 32
14 - 7
Summary of Contents for VASA 6L32
