manualshive.com logo in svg

Wacker Neuson E3000, Operator'S Manual

Share
Download
Wacker Neuson E3000 Operator'S Manual Download Page 80

 ghi_tx001162gb.fm

80

Accessories

E 3000

5.3

Expanded Operation Using One HHS 3002 and One DPP

Requirements

„

Machine stopped

„

One HHS 3002 Hose Handling System

„

One DPP Dual Pump Pack

Procedure

Perform the procedure below to expand the machine with one Hose Handling 
System (HHS) and one Dual Pump Pack (DPP).

1. Position the E 3000 near the application area.

2. Position the DPP 

(a)

 near the application area.

3. Unwind and position the hose 

(b)

 from the left reel of the E 3000 within the 

application area.

4. Unwind and position the hose 

(c)

 from the right reel of the E 3000 within the 

application area.

5. Unwind and position the hose loop 1 

(d)

 from the HHS 3002 

(f)

 within the 

application area. 
a. Connect the male quick-connect to the return port 

(g)

.

b. Connect the female quick-connect to the DPP 

(a)

.

6. Unwind and position the hose loop 2 

(e)

 from the HHS 3002 

(c)

 within the 

application area. Place the HHS 3002 frame in a safe place.
a. Connect the male quick-connect to the return port 

(h)

.

b. Connect the female quick-connect to the DPP 

(a)

.

7. Connect the leader hose of the DPP to the accessory supply port 

(#1)

.

8. Connect the electric cord of the DPP to the Auxiliary Pump Panel. See topic 

Mounting the Auxiliary Pump Panel

.

Result

The machine is now ready for expanded operation.

This procedure continues on the next page.

Summary of Contents for E3000























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands