Wacker Neuson E3000 Operator'S Manual Download Page 160

Page: 160 / 214

wc_tx002068gb.fm

160

Genset Maintenance

Onan Genset

9.5

Replacing the Air Filter Element

Requirements

Engine stopped

New air filter element

Removing

Perform the procedure below to replace the air filter element.

1. Disconnect the battery.

2. Remove the front access cover

(a)

3. Remove the wing nuts

(b)

, bracket

(c)

, filter housing

(d)

, and the filter element

(e)

Installing

1. Perform the procedure below to install the air filter element.

2. Install the new air filter element using the filter housing, bracket, and wing nuts.

Tighten wing nuts hand tight.

3. Reinstall the front access cover.

4. Reconnect the battery.

Result

The air filter element has now been installed.

wc_gr008038

Summary of Contents for E3000























































































































































































































Search results

Summary of Contents for E3000

Reviews:

Brands by name

Popular brands

Wacker Neuson E3000, Operator'S Manual

Search results

Summary of Contents for E3000

Reviews:

Brands by name

Popular brands