Wacker Neuson E3000 Operator'S Manual Download Page 63

Page: 63 / 214

wc_tx001951gb.fm

E 3000

Operation

4.22

Unwinding and Positioning the Hoses

Requirements

HTF preheated if applicable

HTF flow initiated

Procedure

Follow the procedure below to unwind and position the hoses.

1. Rotate the T-handle

(a)

counter-clockwise to unlock it.

2. Pull the hose

(b)

off the reel by hand and place it in the application area. See

topic

Hose Spacing Guidelines

for hose spacing recommendations based on

application.

Result

The hose is now positioned and the machine is operating.

NOTICE:

The machine must be periodically monitored during operation to ensure

system efficiency. See topic

Monitoring the Operating Parameters

CAUTION

Burn hazard. The hoses and components of the plumbing system may be very hot.
Hot hoses and hot plumbing components may cause burns.

Wear gloves when handling hot hoses and plumbing components.

wc_gr008535

wc_gr008530

Summary of Contents for E3000























































































































































































































Search results

Summary of Contents for E3000

Reviews:

Brands by name

Popular brands

Wacker Neuson E3000, Operator'S Manual

Search results

Summary of Contents for E3000

Reviews:

Brands by name

Popular brands