manualshive.com logo in svg

Wacker Neuson E3000, Operator'S Manual

Share
Download
Wacker Neuson E3000 Operator'S Manual Download Page 157

wc_tx002068gb.fm

157

Onan Genset

Genset Maintenance

9.3

Changing the Engine Oil and Oil Filter

Requirements

„

Engine warm

„

New oil filter

„

Fresh, clean oil

Draining oil

Perform the procedure below to change the oil and oil filter.

Note: 

In the interests of environmental protection, place a plastic sheet and a 

container under the machine to collect any liquid which drains off. Dispose of this 
liquid in accordance with local environmental protection laws.

1. Operate the genset until warm, then stop the engine.

2. Pull the oil dipstick/plug out approximately 5 cm (2 in.) to allow the oil to drain 

faster.

3. Remove the front and bottom access covers.

4. Position the drain hose 

(a)

 into a container.

5. Open the drain valve 

(b)

 and drain the used oil. Dispose of used oil in 

accordance with local environmental protection laws.

6. Close the drain valve.

This procedure continues on the next page.

wc_gr008138

wc_gr008036

a

b

Summary of Contents for E3000























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands