manualshive.com logo in svg

Wacker Neuson E3000, Operator'S Manual

Share
Download
Wacker Neuson E3000 Operator'S Manual Download Page 162

 wc_tx002068gb.fm

162

Genset Maintenance

Onan Genset

Continued from the previous page.

2. Loosely secure the filter and filter bracket 

(f)

 to the generator with the two filter 

bracket mounting screws 

(e)

 and reconnect the fuel lines 

(a 

and

 b)

. 

Note:

 

Take care not to cross-thread the fuel fittings. Thread them in by hand 

and tighten one flat past seating

. 

3. Tighten the filter mounting nut 

(d)

 and filter bracket mounting screws 

(e)

.

4. Reinstall the access cover using the flare nuts.

Prepare the 
machine

Prepare the machine for operation.

1. Reconnect the battery.

2. Open the fuel supply valve.

3. Replace any covers, guards, or access panels.

4. Prime the fuel system. 

„

Hold the control switch to the STOP/PRIME position for at least one minute. 

Note: 

The priming sequence will begin after two seconds.

Result

The fuel filter has now been replaced.

  

Summary of Contents for E3000























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands