Wacker Neuson E3000 Operator'S Manual Download Page 132

Page: 132 / 214

wc_tx002070gb.fm

132

Burner Setup—Gas

E 3000

7.10

Checking and Adjusting the Burner Gas Pressure

Requirements

Machine shut down

Adequate supply gas pressure

Manometer

Checking
pressure

Follow the procedure below to check and adjust the burner gas pressure.

1. Turn the control knob

(a)

to the “OFF” position.

2. Locate the pressure test port

(c)

3. Insert a small screwdriver into the pressure test port and back off the needle

valve two revolutions.

4. Connect the hose of the manometer

(d)

to the pressure test port.

5. Turn the control knob to the “ON” position.

6. Start the machine.

7. With the burner firing, check the pressure reading on the manometer. See

section

Technical Data

for the correct pressure.

This procedure continues on the next page.

wc_gr009000

wc_gr008997

wc_gr008998

Summary of Contents for E3000























































































































































































































Search results

Summary of Contents for E3000

Reviews:

Brands by name

Popular brands

Wacker Neuson E3000, Operator'S Manual

Search results

Summary of Contents for E3000

Reviews:

Brands by name

Popular brands