manualshive.com logo in svg

Wacker Neuson E3000, Operator'S Manual

Share
Download
Wacker Neuson E3000 Operator'S Manual Download Page 142

 wc_tx001803gb.fm

142

Maintenance

E 3000

8.6

Cleaning the HTF Strainer

Requirements

„

Machine shut down

„

Source of clean, warm water

Removal

Perform the procedure below to clean the HTF strainer.

Note: 

In the interests of environmental protection, place a plastic sheet and a 

container under the machine to collect any liquid which drains off. Dispose of this 
liquid in accordance with local environmental protection laws.

1. Loosen, but do not remove, the top screw 

(a)

. 

Note: 

There is a second screw 

(b)

 under the canister 

(c)

. Hold this screw while 

loosening the screw 

(a)

. 

2. Tap on screw 

(a) 

with a hammer to release the gasket seal.

3. Remove the canister 

(c)

 by removing screw 

(a)

—support the canister while 

doing so.

4. Dispose of the HTF that remains in the canister.

5. Remove the gasket 

(d)

 from the canister. Replace it if it is damaged.

6. Remove the strainer basket 

(e)

 from the canister.

7. Rinse the strainer basket and the canister with clean, warm water.

This procedure continues on the next page.

Summary of Contents for E3000























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands