manualshive.com logo in svg

Wacker Neuson E3000, Operator'S Manual

Share
Download
Wacker Neuson E3000 Operator'S Manual Download Page 48

 wc_tx001951gb.fm

48

Operation

E 3000

4.10

General Sequence of Operation

Follow the sequence of operation below. Refer to the specific topic for details.

Task

When/Where

See Topic

1. Check HTF level.

Before leaving for the job site. 
Or, when at the job site before 
daily operation.

4.11 / 4.15

2. Check fuel level.

4.13 / 4.15

3. Position the machine.

At the job site.

4.14

4. Perform pre-starting checks.

4.15

5. Connect power.

4.16

6. Start the generator (if equipped)

4.17

7. Power up the machine.

4.18

8. Run the machine.

—

a. Preheat the HTF (if necessary).

4.19

b. Initiate HTF flow.

4.20

c. Unwind and position the hoses.

4.22 / 4.23

d. Monitor the operating parameters.

4.24

e. Rewind the hoses.

4.25

9. Shut down and pack up the machine.

4.26

Summary of Contents for E3000























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands