manualshive.com logo in svg

Wacker Neuson E3000, Operator'S Manual

Share
Download
Wacker Neuson E3000 Operator'S Manual Download Page 130

 wc_tx002070gb.fm

130

Burner Setup—Gas

E 3000

7.9

Checking the Supply Gas Pressure

Requirements

„

Machine shut down

„

Supply gas turned off

„

Manometer

„

Nipple

Checking 
pressure

Perform the procedure below to check and adjust the supply gas pressure.

1. Shut down the machine and allow it to cool.

2. Close the supply gas shutoff valve.

3. Remove the plug 

(a)

 from the tee fitting.

4. Install a nipple 

(b)

 into the tee fitting.

5. Connect the hose of the manometer 

(c) 

to the nipple.

6. Open the supply gas shutoff valve.

This procedure continues on the next page.

WARNING

Explosion and fire hazard. When combined with air, the gas used for this burner is 
explosive. Explosions can cause severe injury or death.

f

Close the supply gas shutoff valve before continuing with this procedure.

f

Extinguish all sources of ignition before continuing this procedure.

wc_gr009663

a

b

wc_gr009664

c

Summary of Contents for E3000























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands