Wacker Neuson E3000 Operator'S Manual Download Page 24

Page: 24 / 214

Labels

E 3000

wc_si000643gb.fm

2.2

Label Meanings

Ref.

Label

Definition

600

601

Turn the handle clockwise to engage the
hose reel brake.
Turn the handle counterclockwise to release
the hose reel brake.

602

WARNING!
Hot surface hazard.
Wear safety gloves.
Wear eye protection.

For machines powered by

the generator:

Use a 50-50 blend of #2 diesel

and #1 diesel plus additives,

or a 50-50 blend of #2 diesel

and K1 kerosene plus addi-

tives when temperatures

are below 5°F (-15°C).

Use a 70-30 blend of #2 diesel and #1 diesel plus additives or

a 70-30 blend of #2 diesel and K1 kerosene plus additives

when temperatures are in the range 5 to 25°F (-15 to -4°C).

Use a winter-blend diesel when temperatures are above

25°F (-4°C).

For machines powered by

the power utility:

Use 100% #1 diesel plus

additives or 100% K1 kero-

sene plus additives when

temperatures are below

are below 5°F (-15°C).

wc_gr008377

WARNING

WARNUNG

ADVERTENCIA

AVERTISSEMENT

173199

Summary of Contents for E3000























































































































































































































Search results

Summary of Contents for E3000

Reviews:

Brands by name

Popular brands

Wacker Neuson E3000, Operator'S Manual

Search results

Summary of Contents for E3000

Reviews:

Brands by name

Popular brands