Volkswagen 1995 Passat Gasoline Repair Manual Download Page 347

Page: 347 / 369

48-77

Tie rods, removing and installing (power
steering gear - TRW and ZF)

Note:

Observe how tie rods are threaded into power
steering gear:

- Tie rods not secured with locking fluid

- Tie rods secured with locking fluid

When exchanging secured version tie rods use
locking fluid D6 when installing.

Removing

The tie rods can only be removed/installed with
the steering gear removed.

- Seal line connections on power steering gear.

1 - Plastic sealing plugs

2 - Plastic sealing plugs

- Clean outside of power steering gear in vicinity of

the boot.

Page 77 of 99

Steering

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands