Volkswagen 1995 Passat Gasoline Repair Manual Download Page 174

Page: 174 / 369

45-5

Wheel speed sensor and rotor for speed
sensor, removing and installing

Speed sensor

When installing speed sensor ensure wiring is

not twisted.

Before installing speed sensor, clean mounting

hole and coat with lubricating paste, G 000 650.

Rotors

Before installing check that rotor is clean and

undamaged.

Front axle

Vehicles with base suspension

Page 40-

Vehicles with plus suspension

Page 40-

Rear axle

Vehicles with rear drum brakes

Page 42-

Vehicles with rear disc brakes (front and four

wheel drive

Page 42-24

Page 5 of 5

Anti-locking Brake System (ABS) and Anti-locking Brake System with Electronic Differential Lock (A...

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.1

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands