Volkswagen 1995 Passat Gasoline Repair Manual Download Page 284

Page: 284 / 369

48-14

- With engine running at idling speed. Close cut-

off valve (not longer than 5 seconds) and read
off pressure.

Specification: 85 - 95 bar (1232 - 1377

psi)

Note:

If the reading is higher or lower than specified
replace pump.

Vehicles with up to 110 kW engine

Page 48-

Vehicles with 128 kW engine

Page 48-97

If reservoir fluid level is low then check steering
system for leaks.

For leaks at the pinion first check the lines/line
connections for leaks and if necessary tighten
and wipe dry.

If the pinion seal or the rack seals in steering
box housing are leaking then replace steering
gear.

To check the rack seals loosen the clamp on
the boot and push to one side.

Page 14 of 99

Steering

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands