Volkswagen 1995 Passat Gasoline Repair Manual Download Page 181

Page: 181 / 369

45-12

After separating ABS control module from ABS
hydraulic unit, always install valve dome
transportation protection on hydraulic unit.

Warranty claims for ABS hydraulic units on which
the valve dome transportation protection was not
used will not be accepted.

Removing

CAUTION!

Determine correct radio anti-theft coding
before disconnecting the battery.

- Disconnect battery Ground (GND) strap.

- Remove coolant expansion tank and swing to

one side.

Page 4 of 9

ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master cylinder (Teves 20 GI), servicing

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.3

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands