Volkswagen 1995 Passat Gasoline Repair Manual Download Page 91

Page: 91 / 369

40-77

Triple-rotor joint, disassembling

- Open hose clamp

- Open clamp on shaft small end and push back

boot.

Note:

- Drive screwdriver or similar tool into cover and pry

open.

If the cover will not pry open, insert screwdriver
and pry from the opposite side.

The cover is destroyed in the removal process. It
does not need to be replaced.

Page 77 of 82

Front Wheel Suspension, Shafts and Axle

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands