Volkswagen 1995 Passat Gasoline Repair Manual Download Page 184

Page: 184 / 369

45-15

Installing

Note:

Remove the sealing plugs from a new ABS
hydraulic unit one at a time, and only when the
corresponding brake line is to be connected.

If the plugs are removed too soon, brake fluid
can escape and it can no longer be certain that
the unit is sufficiently filled or adequately bled.

- Mount ABS control module to hydraulic unit

using new bolts.

Tightening torque: 4 Nm (35 in lb)

- Reconnect ABS hydraulic pump connector.

The remainder of the installation procedure is the
reverse of removal, with the following additions:

- Bleed brake system

Page 47-29

Page 7 of 9

ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master cylinder (Teves 20 GI), servicing

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.3

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands