Volkswagen 1995 Passat Gasoline Repair Manual Download Page 329

Page: 329 / 369

48-59

Power steering gear, adjusting (ZF)

Note:

Two mechanics are required when adjusting.
Adjust with engine switched off.

- Raise vehicle on hoist.

- Wheels in straight-ahead position.

- By turning the steering wheel to and fro (about

30 to center axis) a knocking noise will be
heard if there is excessive play.

- The second mechanic carefully screws the

adjustment screw -arrow- into the cover until the
knocking noise can no longer be heard inside the
vehicle.

- Complete a road test ensuring that when

maneuvering or negotiating corners the steering
self-centers without sticking.

Page 59 of 99

Steering

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands