Volkswagen 1995 Passat Gasoline Repair Manual Download Page 285

Page: 285 / 369

48-15

Power steering gear, removing and
installing

When working on the power assisted steering
gear:

Absolute cleanliness is required when working

on the power steering.

Thoroughly clean connections and immediate

vicinity before loosening.

Place parts on a clean surface and cover if not

re-installing immediately.

Do not use fluffy cloths.

Only unpack parts immediately prior to

installation.

Only use genuine packed parts.

Vehicles with four wheel drive observe installing

heat shield.

Page 15 of 99

Steering

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands