Volkswagen 1995 Passat Gasoline Repair Manual Download Page 241

Page: 241 / 369

46-45

Brake Light Switch, adjusting

Note:

The Brake Light Switch must be removed for
adjusting.

- Remove trim under instrument panel.

- Disconnect harness connector for Brake Light

Switch.

- Remove Brake Light Switch by turning to right

through 90 .

- Pull Brake Light Switch plunger fully out.

- Depress brake pedal as far as possible by hand,

guide Brake Light Switch through the locating
hole and secure by turning through 90 to left.

- Pull brake pedal back up by hand to stop (Brake

Light Switch is pushed back by one notch).

- Connect harness connector for Brake Light

Switch

- Check function of Brake Light Switch.

- Install instrument panel trim.

Page 9 of 9

Parking brake lever assembly overview

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.6

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands