Volkswagen 1995 Passat Gasoline Repair Manual Download Page 340

Page: 340 / 369

48-70

Sealing ring on toothed rod, replacing

When the sealing rod is replaced it must be replaced

with a new one of the same color

Note the matching of the O-ring to the sealing ring

- Press pliers together with slight pressure on the

sealing ring

- Pry out sealing ring and O-ring

A - Needle nose pliers (standard commercial)

O-ring 30.0 x 1.78/ white sealing ring

O-ring 31.0 x 1.5/black sealing ring

- Slide mounting sleeve 3315/19 onto toothed rod

- Pull O-ring over the tool and insert in the groove of

the piston

Page 70 of 99

Steering

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands