Volkswagen 1995 Passat Gasoline Repair Manual Download Page 74

Page: 74 / 369

40-60

Outer constant velocity joint, checking

The joint should be disassembled to replace dirty
grease or for checking the balls and ball tracks
for wear and damage.

Removing

- Before disassembling mark position of the ball hub

in relation to the ball cage and housing with an
electric scriber or oil stone.

- Swivel ball hub and ball cage.

- Remove balls one after the other.

- Turn cage until the two rectangular windows

(arrow) are aligned with the joint housing.

- Lift out cage together with hub.

Page 60 of 82

Front Wheel Suspension, Shafts and Axle

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands