background image

48-66

 

     For easier installation of the puller, it is recommended 

that a rubber band be placed around the jaws. 
Illustration shows the housing in cross section for 
better view.  

Sealing ring for valve body, removing 

 

1 - Puller e.g. Kukko 21/4 

2 - Rubber band 

3 - Sealing ring 

4 - Housing 

    

When installing the puller A, make sure that the claws 
(arrows on fig. N48-0058, 

page 46) engage 

correctly under the sealing ring. The puller must not 
be spread too wide because otherwise the seat for 
the sealing ring and the housing will be damaged or 
the sealing ring can jam in the housing.  

-  Drive sealing ring out toward the top 

A - Puller, e.g. Kukko 21/4 

B - Driver 

-  Drive out lower ball bearing with VW 439 

Page 66 of 99

Steering

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Reviews: