Volkswagen 1995 Passat Gasoline Repair Manual Download Page 95

Page: 95 / 369

40-81

Note:

A seal is formed directly between the triple-rotor joint
and the drive flange by the rectanular sealing ring.
The cover is no longer required.

- Install rectangular sealing ring (arrow) from repair

kit.

90 grams into joint and 90 grams behind joint

- Press 180 grams of axle shaft grease from repair

kit into triple-rotor joint .

- Install triple-rotor joint boot.

- Install boot clamp.

Page 81 of 82

Front Wheel Suspension, Shafts and Axle

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands