Volkswagen 1995 Passat Gasoline Repair Manual Download Page 269

Page: 269 / 369

47-28

Brake system, bleeding (with pressure
bleeder VAS 5234)

Opening the hydraulic unit bleed screws on
vehicles with ABS, ABS/EDL is not permitted!

Bleeding sequence

Note:

- Connect VAS 5234 Brake filler and bleeder unit.

- Open bleeder screws in the specified order and

bleed brake calipers and wheel cylinders.

1 - Right rear wheel cylinder/brake caliper

2 - Left rear wheel cylinder/brake caliper

3 - Right front brake caliper

4 - Left front brake caliper

On vehicles with brake pressure regulator move
the regulator lever when bleeding rear brakes.

Depress the brake pedal several times during
bleeding.

Page 2 of 3

Brake system, bleeding

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.47.6

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands