Volkswagen 1995 Passat Gasoline Repair Manual Download Page 92

Page: 92 / 369

40-78

1 - Triple-rotor joint housing

2 - Triple-rotor star

3 - Axle shaft

Note:

CAUTION!

Do not let the rollers slide off the triple-rotor star
and fall to the floor.

- Remove O-ring -arrow- from groove.

- Mark installation positions of parts -1-, -2- and -3-.

Noises while driving may result if the indicated
parts are not reassembled to their prior positions.

Use a waterproof felt-tipped pen for marking
parts.

- Remove rubber gasket (arrow) from groove.

- With triple-rotor joint housing clamped in vise, pull

axle shaft together with triple-rotor star upward out
of housing.

- Hold axle shaft in straight alignment to triple-rotor

joint and slowly push back triple-rotor joint housing
with other hand.

- Mark installation position of rollers -1- on triple-

rotor star -2- using felt-tipped marker.

Page 78 of 82

Front Wheel Suspension, Shafts and Axle

12/7/2004

http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Summary of Contents for 1995 Passat Gasoline


















































































































































































































































































































































































Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands

Volkswagen 1995 Passat Gasoline, Repair Manual

Search results

Summary of Contents for 1995 Passat Gasoline

Reviews:

Related manuals for 1995 Passat Gasoline

Brands by name

Popular brands