UniData Communication Systems UNIFIBER GIGAROUTER UF72N User Manual Download Page 198

Page: 198 / 210

Gigarouter

UF72N User Manual

Page 190 of 203

Smaller, Moderate, Larger, Maximum

►

DTMF Transfer Model:

Select DTMF transmission mode

: In-Band, INFO, RFC2833

►

RFC2833 Load Type:

If RFC2833 is selected, specify payload type

of RFC2833.

►

T38 Max FAX Rate:

Select the maximum rate, when using T38 fax mode:

Unlimited,

2400bps, 4800bps, 7200bps, 9600bps, 12000bps, 14400bps

►

T38 Signaling Redundancy:

Configure the redundancy of T38 signal.

►

T38 Data Redundancy:

Configure the redundancy of T38 data.

►

Ring Frequency:

Choose the ring frequency:

20Hz, 25Hz

►

Impedance Type:

Choose the impedance type:

600

, China Standard,

Switzerland Standard

4.4.6 Digitmap

The command “show digitmap” shows digitmap information as below:

Figure 4-145 Show Digit Map Parameter

The command “set digitmap” configures digitmap parameters as below:

Figure 4-146 Configure Digit Map Parameter

►

Enable:

Enable or disable digit map function.

►

Short Timer:

The time of Short Timer in second.

►

Digit Map:

The digit map rules.

4.4.7 Signal Tone

The command “show tone” shows signal tone information as below:

Summary of Contents for UNIFIBER GIGAROUTER UF72N



















































































































































































































Search results

Summary of Contents for UNIFIBER GIGAROUTER UF72N

Reviews:

Related manuals for UNIFIBER GIGAROUTER UF72N

Brands by name

Popular brands

UniData Communication Systems UNIFIBER GIGAROUTER UF72N, User Manual

Search results

Summary of Contents for UNIFIBER GIGAROUTER UF72N

Reviews:

Related manuals for UNIFIBER GIGAROUTER UF72N

Brands by name

Popular brands