manualshive.com logo in svg

UniData Communication Systems UNIFIBER GIGAROUTER UF72N, User Manual, Page: 175 / 210

Share
Download
UniData Communication Systems UNIFIBER GIGAROUTER UF72N User Manual Download Page 175

  Gigarouter 

UF72N User Manual

 

Page 167 of 203 

 

►

 

Remote Subnet IP & Remote Subnet Netmask:

 Specify IP address range on your remote network 

to identify which PCs on the remote network are covered by this policy. 

►

 

IKE Safety Policy:         

Specify the IKE policy. 

 

►

 

Enable Safety Prososal: If enabled, 

Select IPSEC Proposal.   

 

4.3.7  Routing 

4.3.7.1  Static Route 

4.3.7.1.1    IPv4 

The command “show static-route ipv4” shows the IPv4 static route information as below: 

 

Figure 4-113  Show IPv4 Static Route Information 

 
The command “set static-route ipv4” configures the IPv4 static route as below.   

 

Figure 4-114  Configure IPv4 Static Route 

The following items are displayed on this screen: 

►

 Enable:                       

Select it to add and modify the current route. Conversely, disable the current 

route. 

►

 Destination IP:

            Enter the destination host the route leads to. 

►

 Netmask: 

                   

Enter

 

the Subnet mask of the destination network. 

►

 Next Hop Type: 

        Include 

Next Hop Interface

 and 

Next Hop Address

(see following option) 

►

 Next Hop Interface:

   

Specify the interface of next hop for current route

 

►

 Next Hop Address:   

Specify the address of next hop for current route

 

►

 Valid: 

                           

Show the status of current route.

 

 

4.3.7.1.2    IPv6 

The command “show static-route ipv6” show the IPv6 static route information as below: 

Summary of Contents for UNIFIBER GIGAROUTER UF72N



















































































































































































































Reviews:

No comments