UniData Communication Systems UNIFIBER GIGAROUTER UF72N User Manual Download Page 104

Page: 104 / 210

Gigarouter

UF72N User Manual

Page 96 of 203

Figure 4-5 Configure 3G Modem Parameters

The following items are displayed on this screen:

►

SP Network:

Other

Swisscom.

If it is not the target user, you need to select the other.

►

Connect Mode:

Manual

Auto

. The default is Auto.

►

Online Mode:

always online

and

disconnect after idle interval

. The default is “always online”.

The default idle interval is 60 seconds.

Other

is selected, the following parameters appear:

►

Username:

3G network dial-up username.

►

Password:

3G network dial-up password.

►

Dial Number:

3G network dial numbers.

►

APN:

3G network access APN.

►

PIN:

3G networks need to use dial-up PIN code, if not, can be set to empty.

Advanced Parameters

►

Authentication:

3G dial-up authentication,

CHAP

PAP

Auto

are provided. Default is

Auto

►

DNS:

The default is obtained from the dial-up network devices automatically. You can

also configure DNS manually.

►

TCP MSS:

Configure TCP maximum segment, we recommend using the default value.

►

MTU:

Configure 3G link MTU, the default value is recommended

►

Data Link Backup:

When enabled, if WAN uplink port is disconnected, the routing switches to the 3G

link.

►

Heartbeat Address:

Set the heartbeat detecting address of the link, the default configuration is not

required.

The command “show 3gmodem-status” show the 3G modem status as below:

Summary of Contents for UNIFIBER GIGAROUTER UF72N



















































































































































































































Search results

Summary of Contents for UNIFIBER GIGAROUTER UF72N

Reviews:

Related manuals for UNIFIBER GIGAROUTER UF72N

Brands by name

Popular brands

UniData Communication Systems UNIFIBER GIGAROUTER UF72N, User Manual

Search results

Summary of Contents for UNIFIBER GIGAROUTER UF72N

Reviews:

Related manuals for UNIFIBER GIGAROUTER UF72N

Brands by name

Popular brands