Trane UniTrane Fan Coil Installation, Operation And Maintenance Manual Download Page 5

Page: 5 / 160

UNT-SVX07E-EN

ZN010 and ZN510 Operation . . . . . . . . . 103

Sequence of Operation . . . . . . . . . . . . . 103

Binary Inputs . . . . . . . . . . . . . . . . . . . . . . 104

Binary Outputs . . . . . . . . . . . . . . . . . . . . 104

Zone Sensors . . . . . . . . . . . . . . . . . . . . . 104

Tracer ZN520 Controllers

. . . . . . . . . . . . . 105

ZN520 Stand-Alone Operation . . . . . . . 105

ZN520 Operation . . . . . . . . . . . . . . . . . . 105

Sequence of Operation . . . . . . . . . . . . . 106

Occupancy Modes . . . . . . . . . . . . . . . . . 106

Cooling Operation . . . . . . . . . . . . . . . . . 107

Heating Operation . . . . . . . . . . . . . . . . . 107

Fan Mode Operation . . . . . . . . . . . . . . . 108

Electric Heat Operation . . . . . . . . . . . . . 109

Damper Options . . . . . . . . . . . . . . . . . . . 109

Dehumidification . . . . . . . . . . . . . . . . . . 110

Data Sharing . . . . . . . . . . . . . . . . . . . . . . 110

Binary Inputs . . . . . . . . . . . . . . . . . . . . . . 110

Zone Sensor . . . . . . . . . . . . . . . . . . . . . . 112

Tracer UC400 Controller

. . . . . . . . . . . . . . 113

UC400 Stand-Alone Operation . . . . . . . 113

UC400 Operation . . . . . . . . . . . . . . . . . . 114

Sequence of Operation . . . . . . . . . . . . . 114

Occupancy Modes . . . . . . . . . . . . . . . . . 114

Timed Override Control . . . . . . . . . . . . . 115

Zone Temperature Control . . . . . . . . . . 115

Discharge Air Tempering . . . . . . . . . . . . 116

Heating or Cooling Mode . . . . . . . . . . . 116

Fan Operation . . . . . . . . . . . . . . . . . . . . . 116

Exhaust Control . . . . . . . . . . . . . . . . . . . 117

Valve Operation . . . . . . . . . . . . . . . . . . . 117

Modulating Outdoor/Return Air Damper 118

Electric Heat Operation . . . . . . . . . . . . . 119

Dehumidification Operation . . . . . . . . . 119

Peer-to-Peer Communication . . . . . . . . 119

Unit Protection Strategies . . . . . . . . . . . 119

Routine Maintenance

. . . . . . . . . . . . . . . . . . 121

Maintenance Checklist

. . . . . . . . . . . . . . . 121

Air Filters

. . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Coils

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Steam and Water Coils . . . . . . . . . . . . . .122

Coil Winterization . . . . . . . . . . . . . . . . . . .122

Moisture Purge Cycle . . . . . . . . . . . . . . . .123

Cleaning Non-Porous Surfaces . . . . . . . .123

Cleaning Porous Surfaces . . . . . . . . . . . .124

Control Device Replacement

. . . . . . . . . . .124

Drain Pans

. . . . . . . . . . . . . . . . . . . . . . . . . . .124

Removing Main Drain Pan . . . . . . . . . . .124

Removing Auxiliary Drain Pan . . . . . . . .124

Replacing Drain Pan . . . . . . . . . . . . . . . . .125

Cleaning Drain Pan . . . . . . . . . . . . . . . . .125

Fans

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126

Inspecting and Cleaning Fans . . . . . . . . .126

Fan Motors . . . . . . . . . . . . . . . . . . . . . . . .126

Torque Rating . . . . . . . . . . . . . . . . . . . . . .126

Fan Board Assembly . . . . . . . . . . . . . . . .126

Replacing Motors . . . . . . . . . . . . . . . . . . .127

Diagnostics and Troubleshooting

. . . . . . . .129

Fan Coil and Cabinet Heater

. . . . . . . . . . .129

Wireless Zone Sensors (WZS)

. . . . . . . . . .130

Receiver Diagnostics . . . . . . . . . . . . . . . .131

Sensor Diagnostics . . . . . . . . . . . . . . . . .131

Testing Signal Strength . . . . . . . . . . . . . .132

Testing Battery Status . . . . . . . . . . . . . . .133

24 V Power Status Indicator . . . . . . . . . .133

Check Signal Strength on a Site . . . . . . .133

Replacing Sensor Batteries . . . . . . . . . . .133

Manual Association . . . . . . . . . . . . . . . . .134

Disassociation . . . . . . . . . . . . . . . . . . . . .134

Sensor/Receiver Compatibility . . . . . . . .134

Replacing a Failed Sensor or Receiver . .134

Servicing and Testing WZS

. . . . . . . . . . . .135

Servicing and Testing Tools . . . . . . . . . .135

Procedure for Testing Zone Sensor . . . .135

Procedure for Testing Receiver . . . . . . . .135

Forcing a Sensor to Transmit . . . . . . . . .135

Output Power Level . . . . . . . . . . . . . . . . .135

Failure and Default Modes . . . . . . . . . . .135

Measuring Output Resistance . . . . . . . . .136

Cleaning the Sensor . . . . . . . . . . . . . . . . .136

Summary of Contents for UniTrane Fan Coil

































































































































































Search results

Summary of Contents for UniTrane Fan Coil

Reviews:

Related manuals for UniTrane Fan Coil

Brands by name

Popular brands

Trane UniTrane Fan Coil, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for UniTrane Fan Coil

Reviews:

Related manuals for UniTrane Fan Coil

Brands by name

Popular brands