background image

1

48VT---C

Comfort™ 14 SEER Single and Three Phase

2---5 Nominal Tons (Sizes 24---60)

Single Packaged HYBRID HEAT

r

Dual Fuel System

With Puron

r

(R---410A) Refrigerant

Owner’s Information Manual

A170030

Fig. 1 -- Unit 48VT--C

NOTE TO EQUIPMENT OWNER:

For your convenience, please record the model and serial numbers of your new equipment in the spaces

provided. This information, along with the installation data and dealer contact information, will be helpful

should your system require maintenance or service.

UNIT INFORMATION

Model # _____________________________________

Serial # ______________________________________

ACCESSORIES (List type of model #)

_____________________________________________
_____________________________________________
_____________________________________________

INSTALLATION INFORMATION

Date Installed________________________________

DEALERSHIP CONTACT INFORMATION

Company Name_______________________________
Address______________________________________
_____________________________________________
Phone Number _______________________________
Technician Name _____________________________

_____________________________________________

NOTE TO INSTALLER:

This manual must be left with the equipment owner.

Our products are designed, tested and built in accordance with DOE standardized procedures; however, actual operating results and

efficiencies may vary based on manufacturing and supplier tolerances, equipment configuration, operating conditions and installation
practices.

Summary of Contents for Comfort 48VT-C











Reviews: