Trane UniTrane Fan Coil Installation, Operation And Maintenance Manual Download Page 132 | Manualshive

Page: 132 / 160

background image

Diagnostics and Troubleshooting

132

UNT-SVX07E-EN

Testing Signal Strength

To initiate a signal strength test, push the Test button on
the sensor (see location of Test button in

Figure 102

and

Figure 103

).

•

Models WZS: LED1, LED2, and LED3 respond by
indicating signal strength. You can view them on the
sensor (

Table 66

) and the receiver (

Table 67

).

•

Model WDS: Test symbols on the sensor display
indicate signal strength (

Table 66

). LED1, LED2, and

LED3, on the receiver, respond by indicating signal
strength (

Table 67

).

Table 66. Observing signal strength on the wireless zone sensor

User action

LED state

Symbol displayed on WDS Indicates...

None

LED1: Off
LED2: Off
LED3: Off

No Test symbols appear

Normal state
No Test button press.

Press Test button on
the sensor

LED1: Off
LED2: Off
LED3: Off

Associated; no communication with receiver
Associated, but no signal from the receiver
after pressing Test button.

LED1: On
LED2: On
LED3: On
Displays for 5 seconds, then
constantly Off

Excellent signal strength
Good signal margin for reliable communication.

LED1: Off
LED2: On
LED3: On
Displays for 5 seconds, then
constantly Off

Satisfactory signal strength
Adequate signal strength for reliable
communication.
Moving sensor or receiver may improve signal
strength.
Increased channel switching may reduce
battery life.

LED1: Off
LED2: Off
LED3: On
Displays for 5 seconds, then
constantly Off

Poor signal strength
Unreliable communication.
Strongly recommend moving the sensor or
receiver to a better location.

Table 67.

Observing signal strength on the receiver

User action

LED state on receiver

Indicates...

None

LED1: Off
LED2: Off
LED3: Off

Normal state
No Test button press.

Press Test
button on the
sensor

LED1: On
LED2: On
LED3: On
Displays for 5 seconds, then constantly Off

Excellent signal strength
Good signal margin for reliable communication.

LED1: Off
LED2: On
LED3: On
Displays for 5 seconds, then constantly Off

Satisfactory signal strength
Adequate signal strength for reliable communication.
Moving sensor or receiver may improve signal strength.
Increased channel switching may reduce battery life.

LED1: Off
LED2: Off
LED3: On
Displays for 5 seconds, then constantly Off

Poor signal strength
Unreliable communication
Strongly recommend moving the sensor or receiver to a better
location

«
...
130
131
132
133
134
...
»

Summary of Contents for UniTrane Fan Coil

































































































































































Reviews:

No comments

Related manuals for UniTrane Fan Coil

Brand: b-mola Pages: 16

Brand: Magic-Pak Pages: 5

U LIGHT COMBO TRS2075

Brand: IconBiT Pages: 2

Brand: Bionaire Pages: 2

Brand: inventum Pages: 100

Air Boss T1001 Module

Brand: Trion Pages: 23

Brand: Dimplex Pages: 10

Brand: GE Pages: 72

Brand: Hunter Pages: 35

Brand: koppel Pages: 19

Brand: OcaRina Pages: 14

Brand: point Pages: 60

23-11-2234N-001

Brand: Maytag Pages: 23

Brand: BAC Pages: 42

Brand: Roam-air Pages: 9

Euro-Line AS28AL

Brand: Argo Clima Pages: 32

Brand: Midea Pages: 18

FreshHome PlasmaWave WACP150

Brand: Winix Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands