Trane UniTrane Fan Coil Installation, Operation And Maintenance Manual Download Page 131 | Manualshive

Page: 131 / 160

background image

Diagnostics and Troubleshooting

UNT-SVX07E-EN

131

The sensor for a wireless display sensor (WDS) has test
symbols and error codes that appear on the display, and a
test button. See

Figure 103

.

Receiver Diagnostics

LED1, LED2, and LED3, located on the receiver of all
models respond to diagnostics by exhibiting specific
blinking patterns. They respond independently of any user
action (see

Table 64

).

Sensor Diagnostics

LED1, LED2, and LED3, located on the WZS respond to
diagnostics by exhibiting specific blinking patterns. View
their response by pressing the Test button.

Error codes appear on the WDS when diagnostics occur
(see

Table 65

).

Figure 103. WDS shows test symbols and error codes

.

Test symbols

Error code

Test button

Table 64. Diagnostics on the receiver

LED state

Indicates...

LED1: Off
LED2: Off
LED3: 1-blink pattern repeated continuously

1

Disassociated
Receiver is not associated, waiting for a sensor.
Receiver lost communication with sensor.
Receiver has no devices on its wireless personal area network.
Association with a device has been manually removed.

LED1: Off
LED2: Off
LED3: 2-blink pattern repeated continuously

1

Address set to 000
Address not set to between 001–999.

LED1: Off
LED2: Off
LED3: 3-blink pattern repeated continuously

1

Not configured
Receiver configuration properties not properly set (defective receiver).

Note:

1

Blink pattern is On for 1/4 s, Off for 1/4 s, with 2 s Off between repetitions.

Table 65. Diagnostics for wireless zone sensors and error code shown on wireless display sensor

LED state when Test button is pressed
on WZS

Error code shown on WDS Indicates...

n/a

E0, E5, E7

Sensor failure
Replace sensor

LED1: Off
LED2: Off
LED3

1

: 1-blink pattern repeated 3 times

E1

Disassociated
Sensor is not associated with a receiver.

LED1: Off
LED2: Off
LED3

1

: 2-blink pattern repeated 3 times

E2

Address set to 000
Address not set to between 001–999.

LED1: Off
LED2: Off
LED3

1

: 3-blink pattern repeated 3 times

E3

Software error
Replace sensor

LED1: Off
LED2: Off
LED3

1

: 4-blink pattern repeated 3 times

E4

Input voltage too high
No RF transmission is permitted with an input battery voltage
greater than 3.9 V.

Note:

1

Blink pattern is On for 1/4 s, Off for 1/4 s, with 2 s Off between repetitions.

«
...
129
130
131
132
133
...
»

Summary of Contents for UniTrane Fan Coil

































































































































































Reviews:

No comments

Related manuals for UniTrane Fan Coil

Brand: Unitary products group Pages: 68

AM AN4PKH Series

Brand: Samsung Pages: 40

Split Sensira R32

Brand: Daikin Pages: 208

Brand: York Pages: 12

Brand: Mars Pages: 36

Brand: Daikin Pages: 92

GWH24YE-K6DNA1A

Brand: Gree Pages: 86

Brand: Salda Pages: 14

Brand: York Pages: 20

Brand: Amana Pages: 32

Brand: Odorox Pages: 12

Brand: Olimpia splendid Pages: 80

Brand: Montgomery Ward Pages: 9

Brand: Akai Pages: 25

Super Cool FSC16SC

Brand: Fral Pages: 43

Brand: M Confort Pages: 51

Brand: Admiral Pages: 38

DOLCECLIMA ARIA 8

Brand: Olimpia splendid Pages: 220

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands