Toshiba BMS-CT1280UL Manual Download Page 66 | Manualshive

Page: 66 / 167

background image

10

-EN

Air Conditioning Control System (Touch Screen Controller)

Installation Manual

3-2. Attaching the Power Adapter

The power adapter can be installed on a flat surface or on a wall. Do not install it in any other orientation.
Fix with the attached binding band and double-sided tape.

REQUIREMENT

Do not install in the following locations.

• Locations with high humidity or water
• Dusty locations
• Locations in direct sunlight and locations subject to high temperatures
• Locations within 3.28′ (1 m) from televisions or radios
• Outdoors, under awnings, or other locations exposed to rain and dew

Installation allowed

Installation not allowed

* Install so that the power cable that connects

to 120 V AC does not face upward.

«
...
64
65
66
67
68
...
»

Summary of Contents for BMS-CT1280UL








































































































































































Reviews:

No comments

Related manuals for BMS-CT1280UL

Brand: ABB Pages: 139

Brand: ABB Pages: 28

Brand: ABB Pages: 59

Brand: Access Pages: 12

C-NaviGator III

Brand: C-Nav Pages: 20

Brand: Gardner Denver Pages: 22

Brand: B&G Pages: 2

Brand: V2 ELETTRONICA Pages: 72

Brand: K1EL Pages: 46

Brand: Vega Pages: 20

Brand: Balboa Pages: 23

Brand: Balboa Pages: 2

Brand: National Instruments Pages: 72

Brand: National Instruments Pages: 41

MAGNUM ALERT 3000 FIRE ALARM

Brand: NAPCO Pages: 2

Brand: hager Pages: 2

Brand: hager Pages: 4

Brand: Measurement Computing Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands