Toshiba BMS-CT1280UL Manual Download Page 162

Page: 162 / 167

Touch Screen Controller

Owner's Manual

-EN

Warranty and after-sales service

• The warranty period is one year from date of purchase.

• Please check "11. Troubleshooting" (P.79) before requesting a repair. If this does not solve the problem, immediately shut

off the power supply and contact us.

• Please inform us of the following when requesting a repair.

- Customer name
- Address, phone number
- Product model name and serial number
- Installation date
- Failure status (as much detail as possible)

For after-sales service, please contact here.

About the Warranty

About After-Sales Service

Contact for after-sales service (Information)

Tap

, then tap [

-(1)

]

The contact information is displayed.

-(1)

Summary of Contents for BMS-CT1280UL







































































































































































Search results

Summary of Contents for BMS-CT1280UL

Reviews:

Related manuals for BMS-CT1280UL

Brands by name

Popular brands

Toshiba BMS-CT1280UL, Manual

Search results

Summary of Contents for BMS-CT1280UL

Reviews:

Related manuals for BMS-CT1280UL

Brands by name

Popular brands