Toshiba BMS-CT1280UL Manual Download Page 46

Page: 46 / 167

Central management addresses can be assigned automatically to all indoor units.
Following section explains the automatic assignment procedure.

Automatic assignment

Tap [

-(1)] of the [Service settings] items

The following message appears: [Rebooting is necessary when it
is executed. Is it OK?]

Tap [

-(1)]

Connection information is acquired. (This takes about five
minutes.)
If the connection information is acquired, the Central management
address Setting screen appears.

Select Central management addresses to be automatically
assigned from [

-(1)]

If this is tapped, the following message appears: [Automatic
assignment of TCC-LINK1 (or TCC-LINK2) will be performed.
Continue?]

Tap [

-(1)]

Automatic assignment of the Central management address is
performed for the selected TCC-LINK. (This takes about three
minutes.)

-(1)

Summary of Contents for BMS-CT1280UL







































































































































































Search results

Summary of Contents for BMS-CT1280UL

Reviews:

Related manuals for BMS-CT1280UL

Brands by name

Popular brands

Toshiba BMS-CT1280UL, Manual

Search results

Summary of Contents for BMS-CT1280UL

Reviews:

Related manuals for BMS-CT1280UL

Brands by name

Popular brands